Zaxcom ZMT3-PHANTOM2 ultra-small wideband wireless microphone transceiver with phantom power and internal recording
Description
Zaxcom ZMT3-PHANTOM2 ultra-small wideband wireless microphone transceiver with phantom power and internal recording, 1x NP-50 battery compartment
Perfect for boom pole operation or as a body pack transmitter, the ZMT3-Phantom2 works with lavalier microphones as well as condenser, dynamic or ribbon microphones. Weighing only 62g, the ZMT3-Phantom 2 is constructed in a high strength impact resistant nylon polymer casing with rounded edges and machined metal that’s cool to the touch. The ZMT3-Phantom2 can be positioned at top of the boom pole directly behind the microphone instead of near the bottom. By removing the internal or external cable, operators can eliminate any cable noise that can leak into the audio track.
The ZMT3-Phantom2 transmits using 100% digital modulation resulting in audio that’s fully encrypted. Digital encryption is the only way to keep all audio transmission private. A digital transmission also provides audio quality far superior to an analog system. The ZMT3-Phantom2 provides a 110 dB dynamic range with no limiting or compression distortion. An external antenna is added so you’ll receive a terrific range. A balanced 3-pin Lemo connector provides input connectivity. Phantom power is selectable in 3.3V, 12V, 24V, 32V and 48V. External audio and battery status levels are easily visible for the operator.
Audio can be recorded internally to a microSD card using the highly reliable lossless MARF (Mobile Audio Recording Format) which eliminates file corruption common to recordings due to dead battery or early card removal. Equipped with ZaxNet, you can remotely change the frequency, pre-amp gain, output power or place the internal recorder in record, playback and stop modes.
The ZMT3-Phantom2 can be ordered in one of two configurations:
ZMT3.5-P2: covering channels 26 through 38 (512 to 614 MHz)
ZMT3.6-P2: covering channels 36 through 49 (596 to 698 MHz)
TRANSMITTER:
RF Modulation: Proprietary Digital Method
ZMT3.5-P2 RF Frequency Range: 512-614 MHz
ZMT3.6-P2 RF frequency Range: 596-698 MHz
RF Frequency Step: 100 KHz
RF Bandwidth in ZHD48 Mode: 50 KHz
RF Bandwidth in ZHD96 Mode: 100 KHz
RF Bandwidth in XR Mode: 200 KHz
Channel Separation in ZHD48 Mode: as close as 100 KHz (receiver dependent)
Channel Separation in ZHD96 Mode: as close as 200 KHz
Channel Separation in XR Mode: 400 KHz
Antenna Connector: 50 Ohm SSMA Female
TRANSMITTER AUDIO:
Dynamic Range: 110 dB
Distortion: 0.002%
Frequency Response: Mode 0: 20 Hz to 16 kHz / T & M Mode: 0.2 Hz to 16 kHz
High Pass Filter: Off or 30 to 220 Hz, Steps: 10 (6dB Per Octave)
Unbalanced Lavaliere Mic Power: 3.3v @ 50mA max
Balanced Mic Power: 12v @ 50mA max
Balanced Mic Power: 24v @ 10mA max
Balanced Mic Power: 36v @ 10mA max
Balanced Mic Power: 45v @ 10mA max
Mic Connector: 3-Pin Lemo
Mic Configuration: Balanced / Unbalanced (2-wire)
Input Range: -60 to -30 dBu
Mic Impedance: 6.8 k Ohm (680 Ohm with 12v power mode)
ADC Bit-Depth: 24 Bits
ADC Sampling-Rate: 48 kHz
TIMECODE READER / GENERATOR:
Timecode output: 3-Pin Lemo
Clock Accuracy: 1.54 PPM (1 Frame Out in 6 Hours)
Timecode Type: SMPTE
Timecode Frame-Rates: 23.98, 24, 25, 29.97NDF, 29.97DF, 30NDF, 30DF
INTERNAL RECORDING:
Media: MicroSD Card (Flash Memory)
File Format: .ZAX / Converts to BWAV or MP3
2.4 GHz ZAXNET RECEIVER:
RF Frequency Range: 2.403 to 2.475 GHz
RF Modulation: Digital Spread Spectrum
RF Frequency Step: 0.001 GHz (1 MHz)
RF Bandwidth: 1 MHz
Channel Separation: 2 MHz
Sensitivity: -96 dBm
PHYSICAL:
Weight: 62 grams with battery
Dimensions (H x W x D): 55.8mm x 40.6mm x 14mm
Display: Graphic OLED
POWER:
Power Output: 25 / 50 / 75 mW (software selectable)
Battery Type: NP-50 (not included with delivery)
Battery Life: Up to 5 Hours, microphone dependent
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.